Motorola Star Tac

Show IMEI code

If you need to know what's the IMEI code of your phone,

simply press:

* # 06 #

you'll read it on display.

Pin-Out

1) Connected with 22pf to pin 3

2) RF out

3) Connected with 33 pf to pin 8, 33 pf to pin, 33 pf to pin 7

4) BAT_FDBAK

5) MAN_TEST connected with 10k to L275

6) RS232_TX - connected to MCU SPI bus

7) RS232_RX - connected to MCU SPI bus

8) AUDIO_IN

9) AUDIO_OUT

10) Connected with 33 pf to pin 13, 33 pf to pin 14

11) UPLINK -|

12) DOWNLINK -|- DSC bus connected to the BIC

13) DSC_EN_B -|

14) EXT_B+

15) Gnd

Motorola mtac Elite

Show IMEI code

If you need to know what's the IMEI code of your phone,

simply press: * # 06 #

you'll read it on display.

Test Mode

To enter in Nam programming Mode, press:

[arrow up]

000000000000 (12 times zero)

[MR]

now display shows the first step of NAM programming;

simply enter data and move to the next step using:

* (the same key of [left arrow])

Software version

To see software version of your phone you need to short-

circuit antenna ground

with the two nearest pin together in the connector

located under the phone. then:

Power ON the phone

and type:

#19#

now display is showing software version of your phone.

Serial Number

To see the serial number of your phone you need to

short-circuit antenna ground

with the two nearest pin together in the connector

located under the phone. then:

Power ON the phone and type:

#75#

now display is showing the first pair of digits, then

go ahead using

* (the same key of [left arrow])

to show the second pair and so on.

Pin Out

The pins are numbered 1 thru 10 from right to left

ANT- (O) | | | | | | | | | |

1) Audio Ground

2) Ext b+

3) T Data

4) C Data

5) R Data

6) Logic Ground

7) Audio Out - on/off

8) Audio In

9) Manual Test

10) Battery Feedback

Motorola Micro tac

Test Mode

To enter in Nam programming Mode,

you need to short-circuit the first and the third battery

pin from the right, then:

Power ON the phone

display will show "Tacs5", type in:

55

now display shows the first step of NAM programming;

simply enter data and move to the next step using:

* (the same key of [left arrow])

Software version

To enter in Nam programming Mode,

you need to short-circuit the first and the third battery

pin from the right, then:

Power ON the phone

display will show "Tacs5", type in:

19

now display is showing software version of your phone.

Motorola mtac Elite

Test Mode

To enter in Nam programming Mode, press:

[arrow up]

000000000000 (12 times zero)

[MR]

now display shows the first step of NAM programming;

simply enter data and move to the next step using:

* (the same key of [left arrow])

Software version

2) Ext b+

3) T Data

4) C Data

5) R Data

6) Logic Ground

7) Audio Out - on/off

8) Audio In

9) Manual Test

10) Battery Feedback

Motorola 8700

Show IMEI code

If you need to know what's the IMEI code of your phone,

simply press:

* # 06 #

you'll read it on display.

Turn on Clock

PLS NOTE: your feedback reports this trick as working on

a very little series of phones, but we found it's the only

one you can try from the keyboard. If it wont work, here

is a definately more difficult way to make it work, but this

is working on all phones that wont recognize the following procedure.

To turn on the hidden clock on your phone follow the following procedure:

In Setup menu turn ON "extended menu"

in language selection change to "GREEK" or "EAAKA"

exit menu

press key labeled "i" (the info key)

type *#25625# and finally

turn OFF the phone

next time you'll wake up the phone the clock will be on

your display and while surfing menu you'll find the option

to set its time.

RBS Info

To activate RBS info menu simply press:

[][][]113[]1[]OK ("[]" = the block you obtain pressing "*"

for 3 seconds or more)

this procedure seems not to work on all software version

but it's the only one you can try from keypad.

Software Bug

Some 8700 remain frozen after you switched on cell

broadcast; the phone seems to function properly but it

can't origin or receive any calls and turns off when you press any key.